OPERATION

• Step 1- Choose a position where your watch winder can stand safely and upright, make sure it on a horizontal surface in order to allow the optimum operation.
• Step 2- Remove the cushion from the watch winder. After inserting your watch (watch dial facing outwards) on the cushion.
• Step 3- Plug the 3V 1.2A power adapter into the backside of watch winder.

• Step 4- Select rotation direction mode your watch requires. You can choose clockwise(&#8635), counter- clockwise(&#8634) , alternately clockwise/ counter-clockwise(Ω) or Clockwise + Counter-Clockwise (Ω)on the controller panel. Your watch manufacturer can provide the guidance here.

  To stop the winder rotating, turn the controller to “OFF” position.

POWER SUPPLY SPECIFICATIONS

Power adapter: 100V-240V, 50 / 60 Hz Input, 3V 1.2A Output

The battery comartment is locate in the bottom of watch winder (If the product you choose supports battery power supply). Battery Required: 2pcs 1.5V battery (not included).

FEATURES

• Mode1: OFF;
• Mode2: Rotate 4 minutes 30 second Clockwise. Rest for 55 minutes 30 second. Repeat;
• Mode3: Rotate 4 minutes 30 second Counter-Clockwise. Rest for 55 minutes 30 second. Repeat;
• Mode4: Rotate 4 minutes Clockwise. Rest for 26 minutes. Rotate 4 minutes Counter-Clockwise. Rest for 26 minutes. Repeat;
• Mode5: Rotate 6 minutes Clockwise. Rest for 24 minutes. (work 4 hours, rest 8 hours), Rotate 4 minutes 30 second Counter- Clockwise. Rest for 55 mintutes 30 second (work 4 hours, rest 8 hours);
• 5 direction of rotation modes: OFF, Clockwise Mode; Counter-Clockwise Mode; alternating and Clockwise + Counter- Clockwise Mode;
• Ultra-quiet motor with optimal 7.5 turns (+-0.5 turns) per minute;
• Pre-engineered ‘rest & sleep cycle’ to protect the mainspring of your watch from over-winding;

IMPORTANT NOTES

• Before operating the watch winder, please contact your watch manufacturer for the information of TPD (turns per day) and rotation direction requirement of your watch.
• Please do not manually spin the winder because it will damage your watch winder.
• Please remove the power adapter when the watch winder is not used for a long time.
• Please turn off the watch winder before inserting or removing the watch.
• Please DO NOT block the rotator when the watch winder is moving.
• Keep children under 8 years of age away from the watch winder and power cables. Children shall not play with the units.
• Keep the watch winder away from the high magnetic object.
• Do not place the product under the sun or humid places.
• Specifications subject to change without notice in accordance with our policy of continuous product improvement.

MAINTENANCE AND CARE

• Use a microfiber cloth or lint-free cloth to clean the watch winder surface with circular movements. Do NOT placing your winder in direct sunlight.
• Clean the interior regularly with a brush by brushing in the direction of the grain. DO NOT use vacuum cleaners or anywet cleaning tools.
• The motor and electronic pats do not require any maintenanceto ensure the fault-free functions.

TROUBLESHOOTING

There are some factors which generally affect the effectiveness of the winder:

• 1.Check the watch placement in the winder, Your watch should be placed with the dial facing up in the winder.
• 2.Some watches must be fully wound before place into our winder as the power reserve may not be enough to keep the watch wound when removed from your wrist. Please refer to your instruction manual on how to manually wind your watch.
• 3.Please wind your watch manually before placing it into the winder, In some cases, due to the watch design, a steeper winding angle is required .You can prop the back of winder using a book or magazine to increase the angle of the turntable then test the wind again. The vertical the better the chance of the test being accurate.